高圣部品
HIGH HOLY PARTS
HIGH HOLY PARTS
专业电子开关、插座、连接器、精密弹簧厂家
专业为您提供完善的售前、售后服务
专业为您提供完善的售前、售后服务
|
主要技术参数/ Main data |
|||
| 1、RATING（额定值）：1.5A 125V AC | |||
| 2、FUNCTION（接触型式）：1P2T | |||
| 3、TIMING（时间特性）：NO SHORTING | |||
| 4、ELECTRICAL CHARACTERISTICS（电气性能规格） ： | |||
| ITEM 项目 | TEST CONDITIONS 测试条件 | PERFORMANCE 规格 | |
| 4.1 |
CONTACT RESISTANCE 接触电阻 |
MEASURED AT SMALL CURRENT(100mA OR LESS) 在微小电流(100mA)以下，拨动三次后测试. |
100mΩMAX. 100毫欧以下. |
| 4.2 |
INSULATION RESISTANCE 绝缘电阻 |
APPLY A VOLTAGE OF 500V DC FOR 1 MIN. TO FOLLOWING PORTIONS AFTER WHICH MEASUREMENT SHALL BE MADE. {C}(1)BETWEEN BODY AND TERMINAL {C}(2)BETWEEN TERMINALS 输入500V DC 电压1分钟,按以下接触方法测试: {C}(1)外壳与排脚之间。 {C}(2)端子之间。 |
100MΩMIN. 100兆欧以上. |
| 4.3 |
DIELECTRIC STRENGTH 耐电压 |
AC500V(50-60Hz)FOR 1 MIN TRIP CURRENT:0.5mA
BETWEEN TERMINALS. BETWEEN INDIVIDUAL TERMINALS AND FRAME. 输入500V(50-60Hz)电压,1分钟感度电流为0.5mA,按以下接触方法测试: (1)排脚相互之间 (2)排脚与外壳之间 |
WITHOUT DAMAGETOPARTS
ARCING OR BREAKDOWN
ETC 没有绝缘破坏等异常 |
| 5、MECHANICAL CHARACTERISTICS (机械性能规格) | |||
| ITEM 项目 | TEST CONDITIONS 测试条件 | PERFORMANCE 规格 | |
| 5.1 |
OPERATING FORCE 作动力 |
MEASUREMENT SHALL BE MADE ST THE NEAREST POINTF
OF THE COMPONENT OR AT THE POINT 3mm FROM THE
TIP OF THE ACTUATOU(KNOB0) 在距离胶柄3mm作测定点，拨动三次后测试。 |
300gf±100gf |
| 5.2 |
TERMINAL STRENGTH 端子强度 |
A STATIC LOAD OF(500gf)SHALL BE APPLIED
TO THE TERMINAL FOR 15 SEC,IN ANY DIRECTON. 在排脚前端任意一个方向加(500gf)力度测试,时间为15秒. |
MECHANICAL AND
ELECTRICAL
CHARACTERISTICS SHALL
BE SATISFIED WITHOUT
LOOSENESS
OF ACTUATOU. 在端子中没有裂开,松动等异常,满足于机械、电器性能。 |
| 5.3 |
DISPLACEMENT OF ACTUATOR (KNOB) 柄强度 |
A STATIC LOAD OF 10N(1Kgf)SHALL BE APPLIED
TO THE TOP OF THE ACTUATOR(KNOB)AND THEN
DESPLACEMENT SHALL BE MEASURED TO THE
DIRECTION OF THE ARROW. 在柄的前端施加1Kgf的力度,位移应沿印记的方向上定. |
THE LEVER SHALL HAVE
NO SERIOUS DEFORMATION
AND FUNCTION IS
NORMALLY. 柄部无严重变形,可以正常工作 |
| 6、ENDURANCE CHARACTERISTICS (耐久性) : | |||
| ITEM 项目 | TEST CONDITIONS 测试条件 | PERFORMANCE 规格 | |
| 6.1 |
LIFE TEST 寿命试验 |
ENDURANCE WITHOUT LOADING： A SWITCH SHALL BE SUBJECTED TO 10,000 CYCLES AT A SPEED OF 15 TO 18 CYCLES PER MINUTE WITHORT LOADING. 无负荷: 在无负荷的条件下以每分钟15—18回的速度进行10,000次的测试. |
(1)CONTACT RESISTANCE(接触电阻)
200mΩ MAX.200毫欧以下. (2)INSULATION RESISTANCE(绝缘电阻) 50MΩ MIN. 50兆欧以上. (3)WITHSTAND VOLTAGE(耐电压) AC 500V,1 MINUTE.AC 500V 1分钟 (4)OPERATING FORCE(作动力) ±30%INITIAL VALUE. 变化范围初始值±30% (5)WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC. (测试后外表无损伤,并且满足机械性能) |
| 6.2 |
SOLDERA-BILITY TEST 可焊性试验 |
THE TOP OF THE TERMINALS SHALL BE
DIPPED 2mm IN THE SOLDER BATH OF
230±5℃ FOR 3±0.5 SECONDS. 端子顶部被浸入锡焊池中2mm深,温度为 230±5℃,时间为3±0.5秒. |
(1) SOLDER WELTING TIME SHALLBE
3 SEC OR LESS. 焊接时间少于3秒 (2) THE AREA OF SOLDERING SHOULD BE OVER 75% 焊接面积要有75%以上. |
| 6.3 |
RESISTANCE
TO
SOLDERING
HEAT TEST 耐焊性试验 |
SOLDER BATH METHOD: SOLDER TEMPERATURE 260±5℃ IMMERSION TIME3±0.5 SEC IMMERSION DEPTH UP TO THE SURFACE OF THE BOARD 1.6mm DIMENSIONS OF COMPONENT HOLES IN THE PRINTED WIRING BOARD SHALL BEING ACCORDANCE WITH THOSE SPECIFIED IN THES SPECIFICATION. 焊炉焊接的时候温度控制在260±5℃,过炉时间为3±0.5秒,于基板厚度为1.6mm SOLDERING IRON METHOD: BIT TEMPERATURE 350±10℃ APPLICATION TIME OF SOLDERING IRON3±0.5SEC HOWEVER EXCESSIVE PRESSURE SHALL NOT BE APPLIED TO THE TERMINAL. 手焊接的时候温度控制在350±10℃,时间为3±0.5秒,但不能在排脚上施加异常压力 |
WITHORT DEFORMATION OF CASE OR
EXCESSIVE LOOSENESS OF TEMINALS
ELECTRICAL CHARACTERISTCS SHALL
BE SATISFIED. 本体无变形,能满足于机械、电气性能。 |
| 6.4 |
COLD TEST 耐冷试验 |
THE SWITCH SHALL BE STORED AT A TEMPERATURE OF -25±3℃ FOR48HOURS.
THEN THE SWITCH SHALL BE MAINTAINED
AT STANDARD ATMOSPHERIC CONDITIONS
FOR 1 HOUR AFTER WHICH MEASUREMENT
SHALL BE MADE. 放置在温度-25±3℃中48小时后,再放置常温中1小时来进行测试. |
THERE SHALL BE NO DEFORMATION
OR CRACKS IN MOLDED PART. 外观无异常,满足于机械、电气性能 |
| 6.5 |
HEAT TEST 耐热试验 |
THE SWITCH SHALL BE STORED ATA
TEMPERATURE OF70±2℃ FOR 48 HOURS.
THEN THE SWITCH SHALL BE MAINTAINED AT
STANDARD ATMOSPHERIC CONDITIONS FOR 1
HOUR AFTER WHICH MEASUREMENT SHALL BE MADE. 放置在温度70±2℃中测试48小时后,再放置正常室温中1小时来测定. |
THERE SHALL BE NO DEFORMATION OR CRACKS IN
MOLDED PART. 外观无异常,满足于机械、电器性能. |
| 6.6 |
HUMIDITY
TEST 潮湿试验 |
THE SWITCH SHALL BE STORED ATA TEMPERATURE
OF 40±2℃ AND A HUMIFITY OF 90% TO 95%
FOR 96 HOURS.THEN THE SWITCH SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR 1 HOUR AFTER WHICH MEASUREMENT SHALL BE MADE. 放置40±2℃的相对湿度为90%～95%环境中96小时后,再将样板放在正常环境1小时后进行测试. |
|
| 6.7 |
STANDARD
ATMOSPHERE
CONDITIONS 测试标准状态 |
UNLESS OTHERWISE SPECIFIED.
THE STANDARD RANGE OF ATMOSPHERE
CONDITIONS FOR MAKING MEASUREMENTS
AND TESTS ARE AS FOLLOWS: (1)AMBIENT TEMPERATURE:5℃ TO 35℃ (2)RELATIVE HUMIDITY:45% TO 85% (3)AIT PRESSURE :86Kpa TO 106Kpa 在没有指定的情况下测试温度、湿度、气压如下: (1)温度为5℃—35℃. (2)湿度为45%—85%. (3)气压为86Kpa—106Kpa. |
|
| 6.8 |
PRACTICAL
TEMPERATURE
RANCE 使用温度范围 |
AT-16℃—+60℃. 在-16℃—+60℃内使用. |
|
